[Frameworks] Loading two super 8 film in the Lomo Tank

Sun Jan 9 13:50:00 CST 2011

Thanks so much for this, I know the hole you speak of, I'll cover it... Sorry for the late response my email account is full of frameworks posts. 
BestKevin

Date: Mon, 3 Jan 2011 18:00:41 +0000
From: vassilybourikas at yahoo.co.uk
To: frameworks at jonasmekasfilms.com
Subject: Re: [Frameworks] Loading two super 8 film in the Lomo Tank

Hi Kevin, 
The following has nothing to do with the arrangement of your spirals but it does have to do with avoiding light leaks. 
The top screw, the one that is kind of tulip shaped, has a small hole in it.(I am not next to a Lomo tank right now to make a picture but you will locate it for sure) 
Cover that hole. A small piece of decent black gaffer tape will stay there a long time. If you leave it uncovered you will find that light will leak through this hole, and affect the several frames that are directly under it. It will be very visible, specially on the film on the upper deck of your Lomo tank. Blocking that hole hardly affects the flow of the
 chemicals. 
I hope this helps. I tried to read all the other posts on the matter, I apologize if someone has covered this already. 
Happy processing and happy new year, 
Vassily Bourikas LabaAthens 

----------------------------------------------------------------------------------

Vassily Bourikas
THESSALONIKI INTERNATIONAL FILM FESTIVAL, 3-12 December 2010
9 Alexandras Avenue.
TK 11473, Athens, Greece.
-
t: +30 210 8706000 ext.330
m: +30 6948056026
w: filmfestival.gr

From: Kevin Timmins
 <on-one-2 at hotmail.com>
To: frameworks at jonasmekasfilms.com
Sent: Mon, 3 January, 2011 0:13:26
Subject: Re: [Frameworks] Loading two super 8 film in the Lomo Tank

Just want to say thanks to Pip, Carl and Nicky for the help. Really appreciate the info!
Could you please follow the link bellow to a flickr page if you have time: 
http://www.flickr.com/photos/48380644@N06/
I've taken some photos of the pieces and have basically story-boarded the order of operation (well how I think it should go anyway). Pictures one to four show (to me) the only logical way to space everything out by 8mm and thread the whole thing together. The fifth photograph shows the bits left over. There are two screw on spacers, a bush and the handle. Obviously the handle must be used, however I'm still not clear wether to use one spacers, two spacers (one above and one bellow), the bush or none of these pieces at all (just screw in the handle as is sits in picture
 4). 
I'm guessing the height of the handle is pretty important as not to let any light in? Thanks again for the help so far, any tips on what's correct or incorrect would be ace!
BestKevin        

From: nicky.hamlyn at talktalk.net
To: on-one-2 at hotmail.com
Subject: Re: [Frameworks] Loading two super 8 film in the Lomo Tank
Date: Sat, 1 Jan 2011 14:04:10 +0000

Hi Kevin,
The bottom spiral stays as is. You remove the screw-on spacer from the centre of the upper spiral, and the top plate goes on whichever way makes the gap 8mm instead of 16mm.
If in doubt, have a practice with some film,
Nicky Hamlyn.
On 31 Dec 2010, at 16:45, Kevin Timmins wrote:I can have a good guess at how to load two super 8 films into my Lomo tank but I'd rather follow some instructions so as I can be sure I'm doing it right. 
Basically the instructions that came with my tank are translated very very badly. It makes mention of 16mm film under the Loading two Super 8 Films section. There are also references to bits that don't appear in the accompanying images. 
Anyway... can anybody link me to a webpage where it shows me the order of operation for developing two
 roll's of super 8 at the same time.
ThanksKevin
  _______________________________________________
FrameWorks mailing list
FrameWorks at jonasmekasfilms.com
http://mailman-mail5.webfaction.com/listinfo/frameworks

 nicky.hamlyn at talktalk.net

_______________________________________________
FrameWorks mailing list
FrameWorks at jonasmekasfilms.com
http://mailman-mail5.webfaction.com/listinfo/frameworks 		 	   		  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://mailman-mail5.webfaction.com/pipermail/frameworks/attachments/20110109/a665ee83/attachment.html 